 |
| . |
|
Reinforced
Resinoid DEPRESSED CENTER WHEELS |
|
|
|
|
|
Back
to Kinik Products
|
|
|
 Standard
Wheel Marking (Example)
|
|
|
|
Abrasive
|
Grain
Size
|
Grade
|
Bond
Type
|
Shape
|
D
|
x
|
T
|
x
|
H
|
|
A
|
24
|
Q
|
BF
|
27
|
180
|
x
|
6
|
x
|
22
|
|
|
|
|
|
Recommendations
|
|
|
|
Workpieces
Features
|
Steel
& iron
|
Cast-iron
Steel
|
Stainless
Steel
|
|
All
Purpose
|
A
24 Q
A
30 Q
|
A
24 Q
A
30 P
|
WA
30 Q
|
|
Long
Life
|
A
24 R
AZ
24 R
|
A
24 R
A
24 Z
|
WA
24 Q
|
|
Free
Cut
|
A
36 P
|
|
WA
36 P
|
|
For
high speed
4800m/min
= (80m/s)
|
A
24 S
AZ
24 S
|
A
24 S
AZ
24 S
|
WA
30 P
|
|
|
|
|
Standard
Sizes (mm)
|
|
|
|
O.D.
( D )
|
Thickness
( T )
|
I.D.
( H )
|
|
50mm
( 2 ")
|
3.
|
9.53
|
|
65mm
(2-1/2" )
|
3.
4.
|
9.53
12.70
|
|
75mm
( 3 " )
|
3.
4.
|
9.53
16
|
|
100mm
( 4" )
|
3.
4. 6.
|
9.53
15 16
|
|
115mm
( 4-1/2" )
|
3.
4. 6.
|
22
|
|
125mm
( 5 " )
|
3.
4. 6.
|
22
|
|
150mm
( 6 " )
|
3.
4. 6.
|
22
|
|
180mm
( 7 " )
|
3.
4. 6.
|
22
|
|
205mm
( 8 " )
|
3.
4. 6.
|
22
|
|
230mm
( 9 " )
|
3.
4. 6.
|
22
|
|
| Note
: |
The
actual hole size listed above are 15.88(5/8¡¨)
for 16mm and 22.23 for 22mm |
|
|
|
|
Operation
Guide
|
|
|
| 1. |
Please
do not operate the grinding wheel in excess of its speed limit. Check
the RPM before using it. When using several pneumatic grinders at the
same time, make sure each grinder has its own pressure regulator to
prevent surges caused by some of the grinders being turned off. The
increased speed may cause damage to the wheel or the operator. |
| 2. |
When
mounting the wheel must be centered perfectly on the shaft. Make sure
there is no wobble in any direction before screwing the caps on.
|
| 3. |
Recommended
angles of operation. Finishing : 5o
to 20.
General operation :20o
to
30o
High
efficiency operation : 30o
to
40o
|
| 4. |
Always
use a safety guard and wear mask & protective glasses to protect
your eyes. |
| 5. |
Do
comply with national safety of grinding wheels.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
